jr mechanics

2010年11月21日 星期日

RE: Stress-strain diagram

 

Stress-strain diagram

Sunday, November 21, 2010

17:20

Description: Machine generated alternative text: Suppose that a metal specimen be placed in tension-compression-testing machina As the axial load is gradually increased in increments, the total elongation over the gauge length is measured at each increment of the load and this is continued until failure of the specimen takes place- Knowing the original cross-sectional area and length of the specimen. the normal stressa and the strain can be obtained The graph of these quantities with the stressa along the y-axis and the strain along the x-axis is called the stress-strain diagram The stress-strain diagram differs in form for various materials- The diagram shown below is that for a medium-carbon structural steeL Metallic engineering materials are classified as either ductile or brittle materials- A ductile material is one having relatively large tensile strains up to the point of rupture like structural steel and aluminum. whereas brittle materials has a relatively small strain up to the point of rupture like cast iron and concrete- An arbitrary strain of O-05 mmimm is frequently taken as the dividing line between these two classes t V) Actual Rupture Strength ??.. U ? Ultimate Strength L E ? Elac L P ? Propoftional Limit Strain, s  R ? Rupture Strength ? Y ? Yield Point Stress-strain diagram of a medium-carbon structural steel

Description: Machine generated alternative text: Proportional Limit (Hooke Law) From the origin O to the point called proportional limit, the stress- strain curve is a straight lina This linear relation between elongation and the axial force causing was first noticed by Sir Robert Hooke in 1678 and is called Hooke Law that within the proportional limit, the stress is directly proportional to strain or u ac e or u = ke The constant of proportionality k is called the Modulus of Elasticity E or Young Modulus and is equal to the slope of the stress-strain diagram from O to P. Then o? = EF Elastic Limit The elastic limit is the limit beyond which the material will no longer go back to its original shape when the load is removed, or it is the maximum stress that may e developed such that there is no permanent or residual deformation when the load is entirely removed Elastic Limit The elastic limit is the limit beyond which the material will no longer go back to its original shape when the load is removed, or it is the maximum stress that may e developed such that there is no permanent or residual deformation when the load is entirely removed Elastic and Plastic Ranges The region in stress-strain diagram from O to P is called the elastic range- The region from P to R is called the plastic range. Robert Hooke

Description: Machine generated alternative text: Yield Point Yield point is the point at which the material will have an appreciable elongation or yielding without any increase in load Ultimate Strength The maximum ordinate in the stress-strain diagram is the ultimate strength or tensile strength Rapture Strength Rapture strength is the strength of the material at ruptureS This is also known as the breaking strength Modulus of Resilience Modulus of resilience is the work done on a unit volume of material as the force is gradually increased from Oto P. in Nm/m3 This may be calculated as the area under the stress-strain curve from the origin O to up to the elastic limit E (the shaded area in the flgure) The resilience of the material is its ability to absorb energy without creating a permanent distortion. Modulus of Toughness Modulus of toughness is the work done on a unit volume of material as the force is gradually increased from O to R. in N-m1m3 This may be calculated as the area under the entire stress strain curve (from O to R). The toughness of a material is its ability to absorb energy without causing it to breat

Description: Machine generated alternative text: Working Stress, Allowable Stress, and Factor of Safety Working stress is defined as the actual stress of a material under a given loading The maximum safe stress that a material can carry is termed as the allowable stress. The allowable stress should be limited to values not exceeding the proportional limit. However, since proportional limit is difficult to determine accurately. the allowable tress is taken as either the yield point or ultimate strength divided by a factor of safety. The ratio of this strength (ultimate or yield strength) to allowable strength is called the factor of safety.

Description: Machine generated alternative text: HELP solution manual in fluid mechanics Hot and Cold working processes Area of the ring between two concentric circles transporation engineering problem Anyone who has autocad video tutorials for 3D? Sand Casting processes Thesis Proposal Assist with cantilever math Two 20 kip vertical forces are applied to a beam Largest value of P more The Brand New 2010 Nissan Cube The Toyota Yaris Saves You Money At The Pump Top Reasons For Making Solar Panels Explore the possibilities with the 2010 Ford Explorer How to use solar energy at home more About • Contact us • Disclaimer • Privacy Policy Mathalino.com - Online Engineering Mathematics • Copyright © 2010 Mathalino.com • All rights reserved • Hosted by WebFaction Ads by Google Engineering Materials Aluminum Materials Stress-strain Diagramhttp://www.mathalino.com/reviewer/mechanics-and-str... 3 of 3 11/21/10 17:20

張貼者： Unknown 於 下午6:56 沒有留言:
以電子郵件傳送這篇文章BlogThis！分享至 X分享至 Facebook分享到 Pinterest
較新的文章 首頁
訂閱： 意見 (Atom)

追蹤者

網誌存檔

  • ▼  2010 (1)
    • ▼  11月 (1)
      • RE: Stress-strain diagram

關於我自己

Unknown
檢視我的完整簡介
頂尖企業主題. 技術提供：Blogger.